When the Ariens snowblower is not moving properly or it seems to be making a lot of noise, you will want to address the issue that is causing this to occur.
Some people state they will notice the Ariens snowblower starts becoming slower as time goes on. This is not easy to deal with and it does create issues as time goes on. This is assuming the snowblower keeps working.
One issue that you might be facing is when the Ariens snowblower drive is slipping.
If the Ariens snowblower drive is slipping, the drive belt is likely damaged or needs to be tightened. It’s also important to top up the oil and make sure the gears are undamaged. If any part is damaged, it should be replaced.
You will often assume it’s okay to keep using the Ariens snowblower that is damaged or has a wonky drive belt. This is not a good idea because the belt is only going to worsen and this can put undue stress on other parts of the snowblower.
This article will show you how to fix an Ariens snowblower drive that is slipping.
Table of Contents
How To Fix Ariens Snowblower Drive That Is Slipping
1. Make Sure The Drive Belt Is Undamaged
If the snowblower drive belt is damaged, this is going to have to be replaced.
The drive belt is responsible for getting the snowblower to run properly and making sure it is handling the snow that is going through the auger.
If there is something wrong with the snowblower drive belt, it will become obvious because the snowblower is not going to move properly.
Your best option in a situation such as this is to see whether or not the snowblower drive belt is damaged in the Ariens snowblower.
If it is damaged, take off the snowblower belt and replace it. The snowblower is not going to run until you do this.
2. Tighten The Drive Belt
Another detail to think about with the snowblower drive belt has to do with how loose it is.
Take the time to inspect the Ariens snowblower drive belt and tug on it. Is the drive belt loose? Does it seem to not spin as required when you do it manually?
This is a good way to test the Ariens snowblower drive belt and see what is wrong with it. Sometimes, all you are going to have to do is tighten the snowblower drive belt and it will start working as required.
The reason it loosens can be something as simple as hitting a hard ice patch that causes it to come undone. Don’t fret about this and just tighten the belt to get it to work again.
You will want to always take the time to assess this part of the snowblower belt to see what’s going on with it.
3. Inspect The Oil Level
Just like the drive belt in the Ariens snowblower, you will want to take the time to inspect the oil level.
Is it too low?
When there is not enough oil in the Ariens snowblower, you are going to deal with issues involving how much oil is going through the snowblower.
It has to be enough to keep the snowblower running as you want it to. When there are issues in this regard, you are going to have major issues with how it is running and how sustainable to setup is.
4. Check The Gears For Damage
Another part of the snowblower that can get damaged during the process would be the gear.
The gear is going to be just as responsible for keeping the Ariens snowblower running as the drive belt. While most people are going to take a peek at the drive belt, they might overlook the gear that also has to move smoothly.
When the gear in the snowblower is not turning as required or seems locked, this means it is damaged. You will need to get a read on what is going on with the snowblower gear.
Check this and make sure the gear is turning as required.
It’s important to go through these details when the Ariens snowblower drive is slipping.
If the Ariens snowblower drive is slipping, it’s best to start by checking to see if the belt is loose or damaged. Replace the belt if it is damaged. Another part that might get damaged is the gear and it will also have to be replaced. It’s also recommended to top up the oil in the snowblower.
Work your way through these steps by testing the snowblower drive belt and seeing which part of the Ariens snowblower is not in good shape.
You will eventually learn it is either the drive belt or the gear. In some cases, it will be the oil level in the snowblower that is the root cause of the issue.