Can’t Find Shear Pin Hole! (Solved)

The shear pin is an integral part of the snowblower and has to be treated with care.

The best solution is to take a look at where the shear pin is in the snowblower and then make adjustments as required.

This will depend on what you are looking to do with the shear pin.

One issue people report is when they can’t find the shear pin hole.

To find the shear pin hole, take off the auger gearbox cover at the front, look for a small hole, and read the manual for more information on this part of the snowblower. Once done, remember to re-install the auger gearbox cover.

You don’t want a situation where the wrong part is touched when you are figuring out how to get more out of the snowblower.

The shear pin hole is not hard to locate as long as you know where to look. It will be noticeable once the auger gearbox cover is off.

This guide is going to provide more insight into how to find a shear pin hole and what it looks like.

How To Find Shear Pin Hole

1. Take Off The Auger Gearbox Cover

The first thing you are going to do is know the general location of the shear pin hole.

It will vary slightly depending on the snowblower model you are working on but it is often going to be set up at the front of the machine.

What you are going to be looking for is known as an auger gearbox cover.

The auger is at the front, so the auger gearbox cover is also going to be there. You are going to look for this cover and then attempt to remove it.

You will want to take off the auger gearbox cover and set it aside as you begin to look for the shear pin hole in a snowblower.

Don’t rush this part and make sure to look at where the shear pin hole is after you have taken off the auger gearbox cover.

2. Look For A Small Hole At The Front

You will now want to start looking for a small hole.

As it is named, it is going to be as small as a pin hole.

This is what you are going to uncover as soon as the auger gearbox cover comes off in the snowblower. You will want to assess what is in front of you under the cover and look for that hole.

This hole is what will allow you to make adjustments to the shear pin as you want to.

You are also going to see the auger gearbox at this point.

Both of these are together, which is why they are under the cover. Once the cover comes off, you are going to notice the shear pin hole in the snowblower.

3. Read The Manual For More On The Shear Pin Hole

Let’s also take the time to appreciate the importance of knowing where the auger gearbox is in your snowblower.

You will have to get a read of where it is by going through the owner’s manual.

This is going to make it a lot easier for you to figure out where to look and what to do when it comes to getting more out of the owner’s manual.

If you do this, you are going to see good results and it will turn out as you want it to. Be patient and read the manual as best as you can.

4. Put The Cover Back When Done

You will want to put the cover back when done.

The goal is to make sure you do not disturb the auger gearbox.

The cover should be put back before you attempt to use the snowblower again. This is a safety requirement and something you are going to want to do to keep the snowblower safe.

If you are not taking the time to do this, you are going to see average results and that is the last thing you want to face.

Put the cover back when done and then see what your options are.

Final Thoughts

Can’t find the shear pin hole?

To find the shear pin hole, locate the auger gearbox cover at the front of the machine. Remove this cover and find the small shear pin hole located near the auger gearbox. Always remember to put the auger gearbox cover back once done.

You will want to keep the auger gearbox safe and that is only going to happen when the cover is back in place as it was before.

You will also want to take the time to go through the owner’s manual to see how the shear pin hole works for the snowblower and where it is.

This can make it easier for you when attempting to figure out what the right option is.