When looking at different RV roof materials, it’s important to think about the type you are going to use when setting up the RV roof.
For some, this is going to include using an EPDM RV roof kit.
Before doing this, it’s important to learn how to install an EPDM roof on a camper. This is essential in getting the results that you are after.
To set up an EPDM roof on a camper, start by choosing the right EPDM roof kit, remove the existing roof (plus accessories), set the new EPDM into place, cut holes for the accessories, and then use acrylic adhesive to secure the EPDM. Once done, install the accessories to complete the look.
It’s important to choose the right EPDM RV roof kit while doing this. The market has a number of options and it comes down to choosing one that is long-lasting and is not going to get in the way.
A good EPDM RV roof kit is going to include the roofing material, tape, and adhesive needed to secure the material into place.
When learning how to install an EPDM roof on an RV, you have to account for this step. The right roof kit for the RV is going to make a difference.
Here are the main steps on how to set up an EPDM roof on an RV.
Steps On How To Set Up EPDM Roof On A Camper
1. Remove The Existing Roof
It’s important to start by removing the existing RV roof.
To do this, you are going to notice there are roofing accessories that need to be taken off first. This is going to include the skylight, refrigerator vent, general vent, vent fan pipe, air conditioner, and antenna.
For most of these accessories on an RV, you can use a screwdriver to remove the screws. This will help the accessories come out.
You have to make sure they are out of the way before removing the old roof on an RV.
After you are done, you can then begin digging out the old RV roof.
Get a sharp tool that is going to let you dig into the RV roof. This will help loosen the material as it is likely in place with an adhesive. This will help you take off the RV roof material easily.
2. Set The EPDM Roof Into Place
Now that the area has been cleared of debris and the old RV roof is off, it is time to think about installing the EPDM roof into place.
How are you going to do this?
You are going to do this by installing the new material across the top of the roof. This will ensure it lies flat.
At this point, you will need to begin working on analyzing how to prepare the top of the RV roof.
3. Cut Holes For Vent Into The EPDM Roof
This is a critical step when installing an EPDM roof on a camper.
You are going to need to cut holes for each accessory that was in place before you removed the old RV roof.
For example, you will need to trim spots for the vent, refrigerator vent, air conditioner, antenna, and vent fan pipe. Remember the spots where they were before and then begin cutting them based on the measurements of the accessories.
You will need to take your time with this step to make sure the cuts are seamless and accurate.
4. Use Acrylic Adhesive To Hold The EPDM Roof Into Place
You will need to begin securing the EPDM roof at this point.
How are you going to do this?
You are going to use an acrylic adhesive that will help hold the EPDM roof in place. A new roof for your RV has to account for this. It is the only way you are going to keep the EPDM roof secure.
The right EPDM RV rubber roof material is one that is going to hold with an acrylic adhesive.
This adhesive should be applied at the bottom and is going to be used to press against the top of the camper.
5. Install The Accessories
Once you are done with this step, it’s time to begin working on the accessories.
It is these accessories that you made holes for. It is time to set them into place and make sure they are fully functional.
It should be done based on where the setup was before you begin removing the old RV roof.
Install each part step-by-step and make sure they are stable. This includes testing the parts to see if they are working as they were beforehand.
Final Thoughts
These are the tips on how to install an EPDM roof on a camper.
To install an EPDM roof on a camper, start by choosing the right EPDM RV roof kit, remove the roof accessories (i.e. vent, fan pipe, antenna), remove the old roofing material, and then set the new material into place. Cut holes for the accessories and use an acrylic adhesive to secure the new roofing material. Once done, install the accessories back into place.
This will make sure the camper is back to how it needs to be. This includes stabilizing the camper and making sure it lasts a long time.