How To Get Air Out Of Pool Pump (Simple)

When figuring out how to get the air out of a pool pump, you will need to understand where the air is and what is needed to remove it safely.

It is not always going to be straightforward but it can be done.

You will simply need to learn how to get the air out of a pool pump.

To get the air out of a pool pump, turn off the pump and skimmer valves before setting the main drain to 100%. Next, turn on the pump, skimmer valves, and filter bleed valve to let the air out. Once the air is out, test the pump again.

These are the steps you need to follow when bleeding air from your pump. As long as you do this, you will see great results with how the pool pump works.

Here is more on these steps for getting air out of a pool pump.

Steps On How To Get Air Out Of Pool Pump

1. Turn Off The Pool Pump And Skimmer Valves

To remove the air from a pool pump, you will need to go through a few key steps.

It is these steps that are going to make sure the pump continues to run as required and does not break down in the middle of the process. Remember that you are still pinpointing where the air is in the pump.

In general, you are going to turn off the pool pump.

While doing this, you are also going to take a look at the skimmer valves and turn all of them off too.

 how to get air out of pool pump

2. Set Main Drain To 100%

If you are looking to bleed air from the pool filter, you will need to take the time to set the main drain to 100%.

To do this, you are going to find the main drain valve and fully open it.

This is how you are going to make sure the pressure is there for the air to come out or it is not going to move as required.

In general, setting it to 100% is a good starting point and then you can set it back to where it was after the air is out.

This step is important when you want to learn how to get the air out of a sand filter pump too.

3. Open Skimmer Valves, Pool Pump, and Filter Bleed Valve

Now, it is time to look at the items that were closed during the first step in this process.

Since the main drain valve is now set to 100%, you are going to have the chance to re-test the pool pump.

To do this, you are going to go to the pool pump and turn it on. At the same time, you are also going to turn on the skimmer valves and make sure they are back to how they were beforehand.

Another step is to go to the filter bleed valve.

This is key because you will want to make sure the air does come out of the pool pump properly.

If you do this, you are going to see good results and there will be no more air bubbles in the pool pump.

Those air bubbles can do damage if they remain in the pool pump and the water is also not going to flow as required. Take care of this with this step to make sure the pool pump is 100% functional.

4. Let The Air Come Out

If your pool pump keeps getting air in it, you are going to have to let the air come out with the steps above.

As soon as the filter bleed valve is open, you are going to notice the water flow is going to improve.

Why does this happen?

It is due to the trapped air coming out of the pool pump. You have to give this a few minutes but it should work as required.

If you are still unsure, you will want to go through these steps again and take the time to re-test the pool pump to see how it is running.

Final Thoughts

It is important to look into these details as you learn more about how to get the air out of a pool pump.

To get the air out of a pool pump, start by turning off the pool pump and skimmer valves. Next, set the main drain to 100% and then turn on the pool pump and skimmer valves again. At the same time, turn on the filter bleed valve to let the air out. It will take a few minutes.

This is all you need to do to make sure the pool pump runs the right way. Otherwise, the pool water is not going to flow properly.

A functional pool pump should not be making too much noise and it should be pumping the water freely.