How To Reset OPD Valve On Propane Tank (Explained)

The OPD valve is responsible for making sure the tank does not get overfilled.

It’s a great safety feature that helps regulate how much propane is in the tank. Since it’s possible for a person to overfill the propane tank, this is a good way to keep tabs on things.

If that is the case, you will want to learn how to reset the OPD valve on the propane tank.

To reset the OPD valve on a propane tank, start by turning off the propane, finding the lever or button on the tank near the top, and then pressing it to release the pressure. If the lever now feels loose, this means the pressure is gone and it’s good to go. If not, continue to hold the lever.

You will always want to pay attention to the OPD valve on a propane tank because it does highlight how things are going when it comes to overall safety.

Here is a look at the main steps on how to reset the OPD valve on a propane tank.

Steps On How To Reset OPD Valve On Propane Tank

1. Turn Off The Propane

The first step is to make sure the propane is off.

You don’t want to keep using the propane tank while working on releasing pressure. This is not ideal nor is it safe.

Your best bet is going to be to turn off the propane and make sure it is reset the right way. A lot of people don’t do this and that makes it difficult to understand whether or not the propane tank is overfilled.

You will want to make sure the propane tank is either disconnected or is not pushing propane through to another fixture.

Once you do this, you will be good to go.

2. Find The Lever Or Button At The Top

You will want to find the lever or button at the top.

This is a common mistake that’s made because you won’t know where to look. It’s easy to get confused between the OPD valve and the bleeder valve.

You will want to start looking for a simple button or lever that is going to be near the top. In comparison, the bleeder valve is likely going to be a knob.

You are going to want to make sure to find the button or lever and then see if it is loose. If it is loose, you are good to go and the pressure is already out. If it is not loose, it is time to start working on releasing the pressure in the propane tank.

This is how you are going to reset the OPD valve.

3. Press The Button To Release The Pressure

To reset the OPD valve in a propane tank, it’s time to press the button or lever.

The goal is to release the pressure and this is only going to be activated when you press the button. You are going to press and hold until you are sure the pressure is out.

This is going to take a few seconds.

Do take your time while doing this to make sure all of the pressure is out. Since you are doing this for the first time, you will want to hold it a bit longer.

4. Move The Lever To See If It’s Free

How will you know when all lof the pressure is out of the propane tank and it is not overfilled?

In general, the lever or button is going to let you know.

If it is loose, you are good to go. This means the pressure is gone and the propane tank is not overfilled. If there is a bit of pressure, it is going to remain tight.

It is also possible the tank is not overfilled and that the lever is damaged. This is when it will refuse to budge even when you press it.

At this point, it is best to make sure the lever is either replaced or you change the propane tank as it will be unsafe to use.

Final Thoughts

It’s important to go through the steps mentioned here when finding out how to reset the OPD valve on a propane tank.

To reset the OPD valve on a propane tank, turn off the gas or disconnect the propane tank. Next, look for a lever or button at the top of the tank and press it for a few seconds. This will release the pressure. If it is loose, the pressure is gone. If it is not, the lever is either damaged or there is still pressure in the tank that has to be removed.

Take your time when working on the propane tank as it will require a few seconds to get right.

If you do this the right way, the propane tank is going to remain in good shape for a long time and it will not have excess pressure in it.