It’s difficult to understand what’s wrong with an RV fridge until you take the time to dig deeper into the finer parts associated with the fixture.
One of those parts is going to be the heating element in the RV fridge.
This part might not be in good shape and that is going to be disconcerting. You will want to take a look at what is going on with the RV fridge heating element as soon as you can. This includes finding out how to test the RV fridge heating element.
To test the RV fridge heating element, disconnect the appliance first. Once ready, set up a multimeter and connect it to the heating to test the Ohms rating. If it is low, the part has to be replaced. If not, check the connections to see if that is the issue.
For the most part, the heating element is going to be damaged. This is common among RV fridges and you will want to be prepared for this as you are testing the RV fridge heating element using a multimeter.
The tips that are going to be listed here will go a long way in helping you learn how to test the RV fridge heating element.
Table of Contents
Steps On How To Test RV Fridge Heating Element
1. Disconnect The RV Fridge
You have to make sure power is not going to the RV fridge.
This is a real concern.
You can’t have a situation where power is going to the RV fridge and continues to do so as time goes on. This is when you are going to get frustrated with how the RV fridge runs and it is not going to be as stable as you want it to be.
You will always want to disconnect the RV fridge.
If you are not taking the time to disconnect the RV fridge, you are going to have power running through it and this can be unsafe.
Since you are going to be testing the RV refrigerator heating element, it is best to disconnect the RV fridge and have access to it.
Remember that the heating element is going to be at the back.

2. Use A Multimeter To Test The Ohms
You will now need a way to test the heating element in the RV fridge.
How are you going to do this?
You will need to have the right tool in hand and that is where you are going to want to bring out the multimeter.
This is the best way to see what the continuity is like with the heating element. If there are specific drops in Ohms then you will know this is the problem point and the heating element is defective.
It’s best to test this part properly using the multimeter before you move to the next step in the process.
3. Check Connections
You will also want to make sure you are assessing the main connection points with the heating element.
Is it too loose?
If it is loose then you are going to know this is the problem you are dealing with. It is important to make sure you are checking the connections in greater detail to see what is going on and what the problem might be over time.
When the heating element is not set in the right spot, it is not going to work as you need it to.
4. Replace The Heating Element If The Ohms Reading Is Low
You will need to figure out how to go about replacing the heating element.
This includes seeing if the Ohms reading is too low.
If the ohms reading is too low, this is a sign there is something wrong with the RV refrigerator heating element and this is where your focus is going to have to be.
Otherwise, the heating element is not going to work properly.
When the RV fridge starts dropping power, this can also be a sign some of the parts are malfunctioning. One of those parts will be the heating element.
Look into this to make sure the RV refrigerator is working and the heating element does not have to be swapped out.
Final Thoughts
These are the most important steps on how to test an RV fridge heating element.
To test an RV fridge heating element, it’s best to disconnect the fridge and then access the heating element at the back. Next, connect a multimeter to the heating element to check the Ohms reading. If it is too low, replace the heating element. It’s also recommended to check the main connections to see if it is settled inside the RV fridge.
You always want to check for this to make sure the RV fridge’s heating element is stable.
If you are not doing this, you are not going to see appropriate results.