How To Vacuum A Pool With A Sand Filter (Simple)

When it’s time to vacuum a pool that has a sand filter, you will need to use the right pool vacuum and also make sure it is set up properly.

An improper setup is going to get in the way of how the pool vacuum works and is going to take away from the results.

This is key as you learn how to vacuum a pool with a sand filter.

To vacuum a pool with a sand filter, use a pool net to remove debris from the pool. Next, connect the hose to the vacuum and then to the skimmer before turning the valve to the filter setting. Once done, turn on the pool pump and vacuum the pool as required.

This is key as you learn how to vacuum an above-ground pool with a sand filter or any other type of pool. It is these details that are going to make the process as smooth as it needs to be.

Here is a look at how to vacuum a pool with a sand filter.

Steps On How To Vacuum A Pool With A Sand Filter

1. Use A Pool Net To Remove Debris

You will need to begin by using a pool net.

This is to remove dirt and/or excess debris from the pool. You will not require a pool vacuum to do this, which is why a simple pool net is going to get the job done.

It’s essential to remove debris from the pool using this method before working on the rest of the pool. Otherwise, it’s going to be harder to maximize the process and ensure the pool vacuum cleaner works as required.

how to vacuum a pool with a sand filter

2. Set Up The Hose With The Vacuum And Skimmer

You are now going to begin working on the setup.

The first step is to set up the hose and connect it to the pool vacuum. To do this, you are going to take the hose and connect it to the head. This is a specific spot on the pool vacuum that is designed for the hose.

You will notice it right away.

As soon as the hose is set up, you can then begin placing the vacuum in the pool.

You will also want to take the time to focus on the other end of the hose. This end is going to link to the skimmer.

There is a pool skimmer inlet that is designed for the hose. You are going to hook the hose to this part to complete the setup.

3. Turn The Pool Pump On

At this point, the pool vacuum is going to be ready to go.

You will want to turn on the pool pump.

This is going to get the water moving, which is when the pool vacuum is going to clean the pool with a sand filter.

In some cases, you are not going to get enough power out of the vacuum. This tends to happen with specific setups where the skimmer is not off. This can be done manually by finding the valves.

You can improve how well the pool vacuum cleans the pool by turning down these valves.

4. Vacuum The Pool

Now, you are ready to go.

This is the most important step as you are going to let the pool vacuum do its job. It is going to begin working on removing particles and/or debris in the pool that is not being filtered.

How should you go about doing this?

The best strategy is to work from the corners and focus on the bottom of the swimming pool. The bottom of the pool is a good starting point as most of the debris is going to settle there.

5. Turn Off The Pool Pump

Now, you are going to look at turning off the pool pump.

This is going to stop the suction.

This is essential as it is the only way you are going to want to make sure to disconnect the hose properly without ruining anything associated with the pool. It will also allow you to take out the pool vacuum from the swimming pool safely.

6. Check The Strainer Basket For Debris

It is important to backwash the pool filter. If you want to backwash the pool filter, turn the valve to backwash.

This will help remove anything that is in the filter.

It is not always required but it is good to do this in some situations.

After this, you are going to check the strainer basket for debris. It is possible there is debris in the basket and you will need to remove it. This is easy to do, just take off the basket and empty it.

Final Thoughts

It’s best to focus on these details as you begin concentrating on how to vacuum a pool with a sand filter.

To vacuum a pool with a sand filter, start by using a pool net to remove debris on the surface. Next, connect the hose to the head of the pool vacuum and then the skimmer. Lower the pool vacuum, turn on the pool pump, and let it run while cleaning the pool. Next, turn off the pool pump, remove the pool vacuum, and then check the strainer basket for additional debris.

At this point, the pool vacuum will have done its job and the pool is going to be clean. Cleaning the pool is all about these little details and getting them right.

Follow the steps here and you are going to have a pristine pool in front of you in no time at all.