Guide On Replacing Seals In Log Splitter (Simple)

When it is time to start pinpointing potential weaknesses with a log splitter, you will want to determine where the leaking is happening.

A leaking log splitter is a real concern and it’s going to get to the point where you are going to become unable to use it.

This is why you have to think about preserving the log splitter.

One option is going to be to start replacing seals in a log splitter.

To start replacing seals in a log splitter, take out the parts near the seal that is compromised. Remove excess debris and then use a seal driver to pull out the seal. Once done, set up the new seal and then re-install the parts that you took out.

This process is going to come down to understanding where the compromised seal is in a log splitter. As long as you do this, you are going to get to the bottom of the issue you are facing.

This article is going to show you more about what it takes when replacing seals in a log splitter and how to go about doing things properly.

Steps On Replacing Seals In Log Splitter

1. Uninstall The Part(s) Near The Seal

You will want to start by assessing the log splitter.

This includes seeing where the compromised seal is. You will want to figure out whether or not the seal can be reinforced and what has to be done to get the log splitter back to 100%.

This is the best way to get the results that you covet.

You will want to start with a simple process of looking for the seal and then uninstalling any parts around that particular seal.

This is going to give you access to where the seal is and then you can begin working on replacing it. Until you do this, you are not going to have an easy time getting to the bottom of the issue in front of you and this is going to become challenging to manage.

Always pay attention to how you took off the parts in a log splitter.

Remember that you are going to have to put these parts back when you are done.

2. Remove Debris

Most people are going to dive into the next step right away.

Yes, you will want to get working on the new seal but that is not what you have to do right now. The best place to move to during this process is to look at the debris that is near the seal.

Is there excess debris that needs to be removed? This debris is going to tarnish how well the seal works when you put it into place.

Look to get rid of the debris in the log splitter and then work on the seal.

This is the best way to do things and see great results.

3. Use Seal Driver To Replace The Seal

You are now going to have the debris out of the way, which means it is time to work on the seal.

If the seal in the log splitter is damaged, you will want to use a seal driver to pry it out. This is how you are going to gain access to the seal and make sure it comes off as you want it to.

A lot of people don’t do this and that is why they are unable to replace the seal as soon as they need to. Focus on this and you are going to feel confident in how things are done.

4. Put Everything Back Into Place

You will want to put everything back into place as soon as you are done with the new seal in the log splitter.

The best approach is to make sure you take each part and put it back in the same order.

If you are lucky then it will not take a long time to do this and you might have only taken off one part from the log splitter.

If it is more complicated, then you will want to work backward.

Just go through this step and then test the log splitter to ensure it is working as you want it to.

Final Thoughts

It’s best to look at these steps for replacing seals in a log splitter.

If you are replacing seals in a log splitter, it is best to begin by finding the damaged seal and removing any parts that are in the way. Once done, remove debris from the seal and then take it out using a seal driver. After the seal is out, replace it with a new one, and then put the parts back into place.

This is going to allow the log splitter to start working as it was before the seal broke down.

For the most part, this is going to not take a long time and the log splitter will begin working again as you want it to.