Wet snow is not the same as regular snow.
It is more weighty and that can create issues with a snowblower depending on how it is set up and used. You have to be careful when you are managing a snowblower in wet snow. The wrong move can cause it to stop working.
It’s important to figure out why the snowblower is clogging wet snow.
If the snowblower is clogging wet snow, it’s best to check to see if the auger is turning smoothly and remove debris from the impeller. It’s also recommended to lubricate the auger using WD-40 and never overload the snowblower.
It’s easy to get carried away when it is time to use a snowblower on wet snow. However, this is how the snowblower stops working because it has too much ice in it or the snow gets stuck inside.
It’s best to take your time and gradually work your way through the snow. This is how you are going to keep the snowblower safe.
Look at the information in this guide as you figure out how to fix a snowblower that’s clogging in wet snow.
Table of Contents
How To Fix Snowblower Clogging Wet Snow
1. Lubricate The Auger Using WD-40
It’s important to have WD-40 on standby.
The reason for using WD-40 in a snowblower is to make sure the auger turns well. It is essential for nothing to get trapped in the auger and that tends to happen when there is wet snow and/or ice on the surface.
When the snowblower auger goes over the wet snow, it will start to pick up the weighty snow. This is when it is going to stop working.
You should make things as slick as possible by lubricating the auger using WD-40.
If you want, you should also take the time to lubricate the chute while you are at it. This can be done with the same WD-40.
It is important to make sure nothing in the auger is getting in the way. This is how you are going to keep the auger safe and the snowblower working in different conditions.

2. Remove Debris From The Impeller
One issue people report is when there is debris in the impeller.
You never want a situation where there is too much debris that is in the impeller. It will create a situation where there is excess debris that is going to get in the way.
You should look to keep things simple and ensure you are removing any debris that is trapped there.
It will ensure you do get rid of the mess and it is as clean as it needs to be.
Whether it is the wet snow or ice, you will want to make sure things are done smoothly. This is how you are going to keep things clean.
3. Check To See If The Auger Is Turning Smoothly
You should look at the snowblower auger to see if it turns smoothly.
Sometimes, the snowblower auger is going to be the issue rather than the conditions. When there is too much wet snow in the snowblower, it is going to become weighty enough that it gets trapped.
Instead of digging it out, you will also want to address the root cause too.
In general, you will want to take a look to see if the auger is turning smoothly. This will let you get a better read on what’s going on when it comes to the snowblower.
4. Don’t Overload The Snowblower
Don’t overload the snowblower.
This is a mistake some snowblower owners make and it can become problematic. The idea is to avoid using the snowblower in a way where it is not going to be able to push through the wet snow.
This does happen depending on how much snow there is.
If it is a large hill, it is not wise to push the snowblower through. It will not work and if it does go through, the snow will get clogged in the snowblower.
Wet snow clogged in the snowblower is difficult to get out, so you want to avoid this type of scenario as best as you can.
Final Thoughts
Why is the snowblower clogging wet snow?
If the snowblower is clogging wet snow, start by clearing out the debris from the auger. Next, check to see if the auger is spinning smoothly, and then lubricate it with WD-40. Once done, always avoid overloading the snowblower when there is a mound of wet snow.
This is the best way to keep a snowblower running in all conditions.
Do not force the snowblower through wet snow. It has to be kept under control and learn how to angle it in a way where it will not get stuck.
This is how you will get a snowblower to function at a good speed and it will run well.