When the Traeger auger stops working, this is going to make it difficult for the pellet grill to work as required.
You will have to figure out what is causing the Traeger auger to get into this state and how you can fix it moving forward.
If the Traeger auger keeps jamming, it’s important to remove the controller, disconnect the hopper, remove it from the pellet grill, remove the sheer pin, and then use a wrench to loosen the auger before removing the debris.
In some cases, it will not be a lot of debris in the Traeger auger.
However, there are some situations where you will need to be rigorous when taking out the debris. You will want to do this with a sharp tool to make sure you can dig into the auger to take out the debris.
This article is going to look at what you need to do to fix a Traeger auger that keeps jamming.
Tips To Fix Traeger Auger That Keeps Jamming
1. Remove The Controller
The first step is to go to the controller on the hopper.
It will be on the left side.
You will want to look at how the controller is mounted to the hopper. This is what you are going to want to unscrew to get it to loosen. Until you do this, you cannot take out the hopper from the Traeger.
This will require you to use a screwdriver.
You are going to loosen the screws and then pull out the controller a little bit.
Once you do this, you are going to push the controller through the mounting hole in the hopper. At this point, you will now be prepared to begin taking out the hopper and detaching it from the Traeger.

2. Disconnect Hopper And Remove It From The Grill
This is an important step when it is time to fix a Traeger that keeps jamming.
You will want to look at taking apart the hopper.
You will do this by finding how it is held with the main pellet grill. There is going to be a connector that you are going to work on to loosen it.
This will help you remove the hopper and pull it away from the pellet grill.
Take your time doing this and make sure the hopper does come out smoothly. Since the controller is not out of the way, you are going to have a simple time taking off the hopper to get to the Traeger auger.
3. Remove The Sheer Pin
There will now be a sheer pin that is going to be in the way.
You will need to take off the sheer pin in the Traeger hopper to make sure you access the auger inside.
This is essential.
To do this, you are going to need an Allen key to work on the sheer pin. Look to loosen it and then make sure to set aside the sheer pin for later when you are going to put everything back to how it was.
The goal is to get to the debris in the Traeger auger as that is the only way to fix this problem as soon as you want to.
4. Remove Clogged Debris With A Sharp Tool
The last step is going to be to observe what is going on with the Traeger auger.
If there are issues such as the Traeger overheating or the Traeger not working the right way, you should always take the time to test this part of the pellet grill.
It tends to get clogged and that is when you deal with major issues.
Look to see inside the auger to see what the issue is.
You will notice it is not going to be budging when you pull on it. This is not a good thing. Loosen the auger and then look inside.
You will notice debris in there.
You will want to look for a sharp tool to work on the debris and then dig it out. You do not want anything in the hole.
Final Thoughts
Look into these steps if the Traeger auger keeps jamming.
If the Traeger auger keeps jamming, it is best to remove the connector from the hopper and then detach the hopper from the pellet grill. Once done, loosen the sheer pin and then the auger. This will give access to the debris inside the auger. Remove this debris using a sharp tool to ensure it’s clear.
Once done, you are now going to have a Traeger that moves freely. You can test this with your hand.
A Traeger that is smoking a lot or a pellet grill that makes too much noise is a real concern. You will always want to go back to the auger to see what the issue is.