Traeger Keeps Blowing Fuses (Solved)

It is important to check if a fuse has blown in the Traeger.

If this happens once, it is not a big deal as fuses can go out from time to time. Replace the fuse and then start using the Traeger.

However, what if there is a situation where the Traeger keeps blowing fuses?

If a Traeger keeps blowing fuses, the most likely causes can include a loose power cord, a damaged hot rod, or a malfunctioning auger motor. It’s recommended to disconnect each part, reconnect the wires, and then test the Traeger to see what is the root cause.

Each situation is going to be different.

It is important to get to the bottom of this as the Traeger will not work until you pinpoint the root cause. Disconnect each part and continue to test the Traeger to see how it does.

This is the only way to fix the problem before it starts affecting other parts.

This guide is going to show you how to fix a Traeger that keeps blowing fuses and how to make sure things go ahead as you want them to.

Steps On How To Fix A Traeger That Keeps Blowing Fuses

1. Turn Off The Traeger

When it is time to start checking on a Traeger and its blown fuses, you will need to turn off the fixture.

This is important as you are not going to want a situation where the Traeger continues to ruin the fuses and does not work as you want it to.

The best solution is to turn off the fixture and make sure you are trending towards a solution that will work over time.

The right step is to turn off the Traeger.

You will want to make sure no power is running to the fixture during this process. The reason is to allow you to take a proper look at what is going on inside and where the damaged part is.

If you do this, you are going to see exceptional results and you will feel good about how it turns out over time.

2. Inspect The Hot Rod And Auger Motor

The most common issues tend to involve the hot rod and/or auger motor.

These are two parts that will impact how much power is drawn into the Traeger and how well it works when it is time to heat up.

If there are any connection issues with the hot rod, it is not going to work.

You will want to take the time to not only check the hot rod but also the Traeger’s auger motor. For each part, do it one by one.

For example, start with the hot rod and disconnect it for five minutes. Now, plug it back in and make sure it is in the right spot. Turn the Traeger on and test to see if the fuse works.

If not, then it is the hot rod that is the troublemaker.

If the fuse does work, move on to the next part, which is the auger motor.

3. Inspect The Power Cord

It is common for people to want to look at the power cord and rightly so.

The premise is to see why the Traeger is not working and where the power issues are stemming from. This can include inspecting the power cord to see how it does.

If the power cord is damaged, the fuse will continue to blow out.

Change the power cord in the Traeger to get it to work properly.

Sometimes, you will also notice signs such as a Traeger excessively smoking. This is when power issues might crop up.

4. Reconnect All Wiring

When it comes to getting a Traeger to work the right way, you will want to reconnect the wiring.

This is when you have checked each part, removed the wiring, and then connected it back into place. This is how you will know the wiring is going to work as you want it to.

It’s a must for you to do this.

If you take your time to do this, you are going to feel good about the results and the Traeger will work out as you want it to.

Final Thoughts

It’s important to look into these nuances when it is time to repair a Traeger that keeps blowing fuses.

If the Traeger keeps blowing fuses, it is likely due to a damaged or loose hot rod, auger motor, or power cord. Go through each one by disconnecting the part, waiting five minutes, and then reconnecting it. In some cases, the parts will have to be replaced.

The most important part is to make sure you are aware of which component needs to be replaced.

This is why going through the steps in this guide is key to getting a Traeger to work properly. Take your time during this process and ensure you are on the right path with what you are doing and how you are doing it.