How To Start Vacuuming A Pool To Waste (Simple)

Vacuuming to waste in a pool requires planning.

You will need to understand the steps associated with vacuuming a pool to waste and how the process should unfold for it to turn out as required. It is easy to make mistakes and that might not help with the cleaning process.

This is where the right steps in vacuuming a pool to waste matter.

To begin vacuuming a pool to waste, set the multiport valve to waste, turn off the pump, turn it back on, and close the skimmer lines except for one. Next, close the drain halfway, set the vacuum, let it run, turn off the pump again, close the skimmer valve, set the main drain to 100%, and put the multiport valve to filter, Once done, turn the pump on, open the skimmer valves, and set the main drain to 50%.

This is a long process but it is going to make sure you know how to vacuum a pool to waste.

Here is more on what you need when vacuuming a pool to waste.

Steps On Vacuuming A Pool To Waste

1. Set Multiport Valve To Waste & Turn Off The Pump

Let’s say you want to know how to vacuum a pool to waste, it’s important to understand the settings.

This includes learning how to vacuum an above-ground pool to waste.

For this to happen, you will want to begin by setting the multiport valve to waste and turning off the pool pump at the same time.

You don’t want the pool pump running during this step as it is not good for the pool.

vacuuming a pool to waste

2. Turn On The Pump And Close Skimmer Lines Except For One

To vacuum a pool directly to waste, you need to now turn on the pool pump.

The goal here is to look at the skimmer lines to see what is going on. In general, you will want to close the skimmer lines except for one.

This is the one you are going to be using to clean the pool water.

3. Close Drain Halfway & Set The Vacuum

You are going to want to focus on the main drain during this step.

In essence, the idea is to target the main drain in the pool and set it to 50%. This means only 50% of the water is going to drain through allowing it to be filtered.

This is going to make it easier for you to vacuum the pool when you are looking to vacuum a pool to waste.

4. Vacuum The Pool And Turn Off The Pump Again

When you vacuum a pool to direct waste, it’s essential to let the pool vacuum do its job.

This means you will want to set it with the right head and then make sure it has the time to go through the pool water while filtering it.

This is also going to require you to turn off the pool pump once you are done with the pool vacuum.

5. Close The Skimmer Valve And Open Main Drain To 100%

To vacuum a pool manually, you are going to now need to close the skimmer valve.

It is also important to once again move your focus on the main drain.

As it is going to be set to 50%, you are going to put it back to 100%. This is going to let the water drain as it was beforehand.

6. Put Multiport Valve To Filter

Since the multiport valve is set to waste, you are now going to set it to filter.

This is key as you are going to want to filter the pool water.

The vacuuming has been done, so you are going to want to make sure the pool water is being optimally cleansed. This is going to include letting the pool pump run after you have taken the time to put the multiport valve to filter.

7. Run The Pump And Open The Skimmer Valves

It’s important to run the pool pump at this point.

The goal of running the pool pump is to make sure you are letting it filter the water. It is going to push the water and get it to move as required.

At the same time, you are going to open the skimmer valves that were closed before.

8. Put Main Drain Back To 50% Again

The main drain should also be set to 50% at this stage.

This should complete the job and make sure you do see the results that you were after when vacuuming a pool to waste.

Final Thoughts

These tips will help as you learn more about vacuuming a pool to waste.

When vacuuming a pool to waste, start by turning off the pool pump and setting the multiport valve to waste. Once ready, turn the pool pump back on, shut down the skimmer lines except for one, close the drain by 50%, place the vacuum in the water, and let it run. Now, turn off the pool pump, shut off the skimmer valve, put the main drain back to 100%, and set the multiport valve to filter. At this point, turn the pool pump back on, open the skimmer valves, and then have the main drain set to 50%.

These steps will make sure you are vacuuming the pool properly. When learning how to use a pool vacuum, you need to address the steps that are listed in this guide.

It will make it a lot easier to cleanse the pool water with a vacuum.