Installing an umbrella stand next to a pool is always welcome.
It’s a nice way to accessorize the swimming pool and get it to stand out the right way. It is these simple adjustments to the pool area that are going to resonate with anyone walking around the pool or looking to enjoy their time outside.
With this in mind, you will want to take a look at setting up an umbrella sleeve in concrete.
To set up an umbrella sleeve in concrete, dig a hole in a safe spot that’s wider than the umbrella sleeve. Now, put the sleeve into the hole, pour concrete in, and then smooth it with a trowel. Once done, let the concrete settle.
This process will not take a long time if you install the umbrella sleeve in the right spot.
Here are the main steps on how to install an umbrella sleeve in concrete.
Table of Contents
Steps On How To Put Umbrella Sleeve In Concrete
1. Dig Hole Wider Than The Umbrella Sleeve
Installing an umbrella sleeve next to a pool means finding the right spot.
You will want to make sure the spot is clear from other features around the pool. You do not want to compromise those features by drilling into the concrete and then taking up space where you shouldn’t.
It is important to dig a hole that is wider than the umbrella sleeve.
It’s a simple change that will go a long way in making sure there’s enough space for the umbrella to work as required.
When you are digging, you will want to make sure it’s smooth. This means you shouldn’t be cracking the concrete and/or damaging anything near the swimming pool.
Make sure you drill in a straight line.
The depth of the hole should also be accounted for. This means you will want to make sure the hole is deep enough for the umbrella sleeve to go in.
If this does not happen, the umbrella is going to fall. You have to look at stabilizing the umbrella sleeve and this is the best way of doing so.

2. Insert The Sleeve Into The Hole
When it comes to a built-in pool umbrella, you will need to make sure the umbrella sleeve is going into the hole safely.
This is going to include being patient with how you are inserting the sleeve.
You will want to avoid pushing too hard. Just make sure the sleeve goes into the hole and that it does not budge.
A common mistake that’s made is to have it inserted at an angle. This might allow the umbrella sleeve enough leeway to go into the hole but that is going to make it unstable.
Don’t do this and ensure it’s being inserted in a straight line.
3. Pour Concrete Into The Hole
You are now going to begin working on solidifying the setup.
This is going to include using fresh concrete.
In most cases, you will want to prepare the concrete by mixing it. This will depend on the instructions that come along with the materials in your possession. Follow them to make sure the concrete is ready to go for the process.
Once the concrete is ready, you are going to pour it into the hole.
The purpose of the concrete is to make sure it spreads evenly and holds the sleeve in place. As it dries, the concrete is going to settle the sleeve.
You will also want to smooth the top layer of concrete so it looks clean.
4. Let The Concrete Settle
This is the last step.
You will now have smoothed out the concrete that was poured into the hole. It is essential to let the concrete settle as that is how it is going to hold the umbrella sleeve in the concrete.
How long is this going to take?
It will take approximately 24 hours but it can take longer depending on the conditions. If it is sunny, this can expedite the process.
You will always want to let the concrete settle as that is a must when it comes to maximizing what you are doing and how you are doing it.
Final Thoughts
These are the main steps on how to put an umbrella sleeve in concrete.
To put an umbrella sleeve in concrete, start by finding the right spot and drilling a hole that’s slightly bigger than the sleeve. Now, put the sleeve in and fill the hole with concrete. Let the concrete settle to complete the job.
You will have to make adjustments to ensure the umbrella sleeve does not budge. This includes ensuring it is put in properly. You don’t want to insert the umbrella sleeve at an angle. This will lead to becoming unstable.
Focus on maximizing the setup by stabilizing the umbrella sleeve in the hole. This is how you will get it to look as required.